Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Cap & Crown for Lake Highlands Homeowners
If you’ve noticed a cracked crown or a cap that’s rusted through, you’re looking at the most common way water gets into a Lake Highlands chimney. The crown is the concrete cap at the very top of the chimney, and the cap is the metal hood that covers the flue opening. Together they keep rain, animals, and debris out of the flue and away from the masonry. When either one fails, water starts working into the brick, the mortar joints, and eventually the flue itself. That’s where we come in.
Our technicians have up to 8 years of experience with cap and crown work across Lake Highlands, and chimney repair is all we do. We don’t hand off scopes to subcontractors. From the firebox to the cap, the same specialist handles the job. A cap or crown issue is also easy to catch early during a routine inspection, so if you’re not sure whether yours is holding up, we can look. Estimates are free, and you get a written price before any work is booked. Call (833) 508-9984. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
What Our Chimney Cap & Crown Service Includes
Caps and crowns aren’t one job. They’re a family of related repairs, and which one you need depends on what’s actually failing up there. Here’s how we break it down.
Cap Installation
A chimney cap is the metal cover that sits on top of the flue and keeps rain, birds, squirrels, and leaves out of the chimney. You need one whenever your flue is open to the sky, and that includes new chimneys, older homes where the cap was never replaced, and any flue that has become an animal highway. We install single-flue and multi-flue caps fitted to the actual dimensions of your chimney, using products from lines like Famco and Copperfield that hold up to North Texas sun and weather. Proper mounting matters as much as the cap itself, so we secure it to the flue tile or the crown rather than letting it sit loose.

Cap Replacement
A cap that’s rusted through, dented, loose, or missing its mesh isn’t doing its job. Metal caps typically fail at the seams and along the bottom edge, where water sits, and a loose cap can rattle in the wind and eventually blow off. Replacement is usually straightforward when the flue and crown are sound underneath. We remove the old cap, check the flue tile and crown for damage while we have the access, and install a new cap sized and anchored correctly.

Crown Repair
The crown is the concrete or mortar surface at the top of the chimney that slopes away from the flue to shed water. It cracks with age and thermal movement, and once a crack opens, water runs straight into the masonry below. We repair crowns by removing loose material, addressing the crack properly, and rebuilding the slope so water drains away from the flue instead of into it. This is one of the highest-value repairs on a chimney, because a crown that fails quietly is often the start of much larger masonry work.

Crown Coating
Crown coating is a protective layer applied over a crown that’s still structurally sound but showing surface wear. It seals hairline cracks and slows the deterioration that leads to bigger breaks. You need it when the crown is intact but rough, or after a crown repair to extend the life of the new surface. We apply coatings formulated for chimney crowns and check adhesion at the edges, which is where most coatings fail first.
Multi-Flue Cap
A multi-flue cap covers a chimney with more than one flue in a single unit, common on larger fireplaces and homes with a furnace flue beside the fireplace flue. These are fabricated to the exact footprint of the chimney. You need one when your chimney has multiple flues and either no cap or a set of mismatched singles. We measure the full chimney top, account for flue spacing, and install a single cap with screened openings for each flue.
Custom Cap
Some chimneys don’t fit stock sizes because of an unusual footprint, a curved top, or a decorative crown. A custom cap is fabricated to fit the actual dimensions rather than forced onto a chimney that doesn’t match. You need one when an off-the-shelf cap leaves gaps, sits uneven, or can’t be anchored securely. We take the measurements ourselves and confirm fit before installation.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Brands We Service for Chimney Cap & Crown
We work with cap and crown products from lines the chimney trade actually uses, including Famco, Copperfield, and Olympia Chimney. Famco caps are common on Lake Highlands homes, and we know where their mounting hardware tends to loosen over time, so we check the anchor points closely on every install. Copperfield products show up often on multi-flue jobs, and we’re familiar with how their caps are sized and screened. Olympia Chimney components appear on a range of chimney tops, and we work with their caps regularly when matching a replacement to an existing setup.
Every cap we install is sized for your chimney, not picked off a shelf and hoped into place. Whether you have a Famco cap that’s seen better days, a Copperfield unit that needs re-screening, an Olympia Chimney setup, or any other make, we can help. If the existing cap or crown isn’t a brand we know well, we’ll tell you plainly and work with what’s there or recommend a replacement that fits correctly.
Signs You Need Chimney Cap & Crown Right Now
- Cracks in the crown. Hairline cracks widen as water works into them and the concrete moves. A cracked crown is the single most common entry point for water damage in a chimney, and catching it early is the difference between a coating and a rebuild.
- Rust, dents, or missing mesh on the cap. A rusted or damaged cap lets water and animals through and often means the cap is near the end of its life. If the mesh is torn or gone, birds and squirrels can get into the flue.
- Water staining on the chimney or in the attic. Brown streaks on the exterior brick or damp spots near the chimney in the attic usually trace back to a failed crown or cap. Interior staining and a musty smell near the fireplace point the same direction.
- Loose or missing cap. A cap that wobbles in the wind or has blown off is an open door for rain and debris. It’s also a sign the mounting was never right, which is worth correcting on the replacement.
- Spalling brick or crumbling mortar near the top. Flaking brick and sandy mortar at the top of the chimney usually mean water has been getting in for a while. That’s crown-and-cap territory before it becomes structural masonry repair.
None of these are reasons to panic. They’re reasons to have someone look before winter rain and the next cold front do more damage. A chimney inspection isn’t a formality. It’s how we find small problems before they become expensive ones.
Our Chimney Cap & Crown Process – Step by Step
- 1
Visual inspection from the ground and, when needed, at the top. We start by looking at the chimney from the ground and from a ladder to assess the cap, crown, flashing, and masonry. For anything we can’t see clearly, we use a camera to check the flue and the crown from above. You get a clear picture of what’s wrong before we quote anything.
- 2
Written estimate with line items. We put the recommended work in writing, with each item priced separately so you can see exactly what you’re paying for. If part of the job can safely wait, we tell you that, and we won’t recommend liner or masonry work unless the evidence supports it. You’ll see the photos behind any recommendation.
- 3
Site protection and prep. Before we start, we cover roofing and landscaping below the work area and set up safe access to the chimney top. Caps and crowns are height work, and the setup is part of the job, not an afterthought.
- 4
Repair or installation. We remove failed material, address the underlying cause, and install the new cap or rebuild the crown to shed water correctly. Coatings go on only after the surface is prepped and sound. Every fastening is checked so the finished piece is secure, not just sitting there.
- 5
Final check and photo report. We confirm the cap is anchored, the crown slopes correctly, and the flue is clear. You get photos of the finished work so you can see what was done, plus notes on anything to watch over the coming seasons.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Cap & Crown Cost in Lake Highlands?
A typical chimney cap installation in Lake Highlands runs $150 – $450 depending on flue count and cap style, while a crown repair usually runs $300 – $800 depending on the size of the crown and the extent of the cracking. Crown coating is generally the lower end of that range, and a multi-flue or custom cap sits at the higher end. These are estimates, and the written estimate you receive sets the final price.
What affects cost: how many flues you have, whether the cap is stock or custom, how much of the crown needs rebuilding versus coating, and whether we find related damage during the inspection. Access matters too. A steep roof or tall chimney takes more setup, and that’s reflected honestly in the quote rather than buried.
How to avoid overpaying: get the recommendation in writing with photos. If someone tells you the crown needs a full rebuild, ask to see the crack and the evidence. We’re happy to show you. One repair at the top often prevents thousands in masonry work later, so treating cap and crown work as preventive maintenance is the cheaper path over time. Every estimate is free, and there’s no obligation.
Chimney Cap & Crown Near Lake Highlands – Our Service Area
We serve homeowners across Lake Highlands and the surrounding neighborhoods, including Lochwood, Forest Hills, Lakewood, White Rock, and East Dallas. We also work in Sachse, Rowlett, Garland, Richardson, Casa View, and University Park. Dispatch runs Sunday through Friday, 7am to 7pm, with typical arrival windows of a few hours once a job is booked. If you’re comparing providers, our chimney cap & crown page covers the full scope of what we do, and you can start with a chimney sweep Lake Highlands visit if you’re not sure what’s failing. Homes in Sachse can use our chimney cap & crown service, and Rowlett homeowners can book chimney cap & crown the same way.
Serving Lake Highlands, TX – Our Local Coverage Area
We serve Lake Highlands and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Chimney Cap & Crown in Lake Highlands
The crown is the concrete surface at the top of the chimney, and the cap is the metal cover over the flue opening. Together they’re the chimney’s first line of defense against rain, animals, and debris. When either fails, water gets into the masonry and flue, which is the leading cause of chimney water damage.
Most cap installations take a couple of hours, and crown repairs typically take a few hours depending on how much needs rebuilding. Coating jobs are shorter, and custom or multi-flue caps may need a return visit once the piece is fabricated. We give you a realistic timeline in the written estimate.
A cap installation typically runs $150 – $450, and a crown repair runs $300 – $800, with the written estimate setting the final price. Factors include flue count, cap style, and how much of the crown needs work. Call (833) 508-9984 for an exact quote; estimates are free.
Yes. We work with cap and crown products from Famco, Copperfield, and Olympia Chimney, and we’re familiar with how each of those lines is sized and mounted. If your cap isn’t a brand we know well, we’ll tell you and work with what’s there. Whether you have one of those brands or any other make, we can help.
We can often schedule same-day work when the calendar allows. Fast dispatch runs from 7am to 7pm, Sunday through Friday, and we’re closed Saturday. We answer 24/7, so a call outside dispatch hours is booked into the next opening.
Warranty terms depend on the product and the scope of the repair. We walk through coverage with you in the written estimate so there are no surprises. Manufacturer warranties on caps are handled through the product line, and we’ll explain what’s covered before you book.
Clear access to the fireplace and the chimney area on the roof path if we need it, and secure any pets. That’s usually all it takes. If you have prior inspection reports or photos, have them handy, but it isn’t required.
Schedule Your Chimney Cap & Crown Service in Lake Highlands Today
Whether it’s a cracked crown, a rusted cap, or you just want to know if the top of your chimney is holding up, we can take a look. Call (833) 508-9984 for a free, no-obligation estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. We handle the full scope, from the firebox to the cap, so nothing gets missed.
Written by the team at Chimney Sweep Lake Highlands.